Hi All!
I'm a newbe doing my first steps with VisualMill.
Still can't find a way how to process a part attached.
Can anyone give me a hint or vcp file? Can it be done with VM at all?
How to mill this part?
-
- Posts: 4
- Joined: Thu Apr 19, 2012 12:43 am
How to mill this part?
- Attachments
-
- cil15_kirs.vcp
- (519.15 KiB) Downloaded 1190 times
-
- Posts: 31
- Joined: Wed Aug 01, 2007 4:15 pm
- Location: Montreal Quebec Canada
- Contact:
Re: How to mill this part?
hello I cant open your file ,is .vcp a vcarve pro file ?
Convert it to a Rhino file
I see this is visual mill forum not rhinocam ,I will try to open it with visual mill
Convert it to a Rhino file
I see this is visual mill forum not rhinocam ,I will try to open it with visual mill
-
- Posts: 31
- Joined: Wed Aug 01, 2007 4:15 pm
- Location: Montreal Quebec Canada
- Contact:
Re: How to mill this part?
I tried to open your file with visualmill ,and .vcp files are not supported,
You will have to convert it in your vcp program first . Unless I am missing something
You will have to convert it in your vcp program first . Unless I am missing something
-
- Posts: 4
- Joined: Thu Apr 19, 2012 12:43 am
Re: How to mill this part?
As much as I know VCP are - VisualCamPart files... there shoudn't be problems to open it in VisualMill.
Original file was IGS, but regret I can't attach IGS here... Than I imported that IGS into VisualMill 6.0 and saved. That's it.
Original file was IGS, but regret I can't attach IGS here... Than I imported that IGS into VisualMill 6.0 and saved. That's it.
-
- Posts: 31
- Joined: Wed Aug 01, 2007 4:15 pm
- Location: Montreal Quebec Canada
- Contact:
Re: How to mill this part?
Visualcam part file that make sense but I cannot open it with rhinocam or visual mill
I dont know what to do
I dont know what to do
-
- Posts: 4
- Joined: Thu Apr 19, 2012 12:43 am
Re: How to mill this part?
What's wrong? PLS see PrtScr attached...
I can send IGE to mail if anybody can assist.
I can send IGE to mail if anybody can assist.
- Attachments
-
- VisualCam_PrtScr.jpg (71.24 KiB) Viewed 15642 times
Re: How to mill this part?
I can open your file I will take a look get back to you soon.
Update: I apologize I cannot do anything with this I only have the basic VisualMill no 4th axis.
Good Luck
Update: I apologize I cannot do anything with this I only have the basic VisualMill no 4th axis.
Good Luck
Happy Cutting!
-
- Posts: 4
- Joined: Thu Apr 19, 2012 12:43 am
Re: How to mill this part?
OK, here comes another puzzle - pls see file attached.
Due to total shortage on intelegence I can't mill this part as well. I know its quite easy to produce, but - pls point it out how!
OK, this issue is solved, but previous case is still open.
Due to total shortage on intelegence I can't mill this part as well. I know its quite easy to produce, but - pls point it out how!
OK, this issue is solved, but previous case is still open.
- Attachments
-
- joint.vcp
- (109.53 KiB) Downloaded 1143 times
Last edited by ShadowVoice on Sun May 20, 2012 4:07 pm, edited 1 time in total.
-
- Posts: 2405
- Joined: Wed Aug 01, 2007 4:15 pm
- Location: Irvine, CA, USA
- Contact:
Re: How to mill this part?
I would suggest getting some on-line training from our support department. Questions such as "how do I mill this part" are best addressed in a training session, if some other uses are not able to help you.